I am using DD-WRT v24SP1 on my Linksys WRT 54GL router and I am trying to get the build in DHCPd server to also send the ip address of my TFTP server. In general I need to be able to add option 66 and option 150. I have tried to find other topics that might describe this topic but was unsuccesfull.
26/12/2010 This might sound amazingly stupid but I have a DD-WRT (micro) router that I placed in my network to act as a switch and as a WAP while relying on my cable modem to be the DHCP server. In my attempts to get the configuration right I put the router into DHCP forwarder which then made everything work correctly. The problem is now I can't seem to 2) Allez dans « Setup »> « Configuration de base » et configurez les « Paramètres d’adresses réseau de serveur (DHCP) » suivants sous : DNS statique 1 = 8.8.8.8. DNS statique 2 = 8.8.4.4. DNS statique 3 = 208.67.222.222. Utilisez Dnsmasq pour DHCP = Vérifié. Utilisez Dnsmasq pour DNS = Vérifié. DHCP-Autoritaire = Vérifié 19/07/2016 The DD-WRT Settings; Basic Setup > Network Setup > Router IP > Local DNS should be set to the RPi address (192.168.0.239) , Gateway doesn't matter but I have it set to the modem (192.168.100.1) and the settings Basic Setup > Network Setup > Network Address Server Settings (DHCP) > Static DNS 1 I've set to 192.168.0.239, the other two I've tried #dhcp-option=44,0.0.0.0 # set netbios-over-TCP/IP nameserver(s) aka WINS server(s) 394: #dhcp-option=45,0.0.0.0 # netbios datagram distribution server 395: #dhcp-option=46,8 # netbios node type 396: 397 # Send an empty WPAD option. This may be REQUIRED to get windows 7 to behave. 398: #dhcp-option=252,"\n" 399: 400 # Send RFC-3397 DNS domain search DHCP option. WARNING: Your DHCP …
19/04/2016
About. DD-WRT is a Linux based alternative OpenSource firmware suitable for a great variety of WLAN routers and embedded systems. The main emphasis lies on providing the easiest possible handling while at the same time supporting a great number of functionalities within the framework of the respective hardware platform used. The router is a Netgear R6300v2 running DD-WRT v24-sp2. My ISP uses DHCP for WAN and when I enable transparent bridging (after disabling wifi radio and DHCP server) the DD-WRT router has no internet access and I have to reset the modem and go through the walled garden process all over again. The router is set to auto-config DHCP for WAN. Setting the gateway IP the the modem's IP makes no
So far I've learned of 3 ways to configure the DD-WRT, so that it will perform DNS for your local network. I don't claim to know which way is preferred by the developer(s) of the DD-WRT. Warning : Whatever method you use, you might not "see" the expected results on your computer until you reboot the computer or restart the network interfaces.
Note - option 61 defintely seems to be missing from both DD-WRT and Voxel for the R7800. It would be nice to see it in either, becuase if the connection goes down I have to re-enter and run the command 19/04/2016 · Hi group, I have a LinkSys wrt54g router with DD-wrt install (Firmware: DD-WRT v24-sp2 (08/12/10) micro). DHCP is enabled. By default the DNS is This is an example of my Buffalo WHR-HP-G54 router (with DD-WRT installed) connected devices showing: Active (transmitting) wireless clients. Clients whose DHCP Lease Time has not expired (configured to 180 minutes in my case). As I use to enter the device via SSH, I would like to develop some script to obtain the second table: DHCP Clients List.